Mudah-mudahan dengannya toko online kami bisa memberi banyak manfaat bagi Anda. Salam super dan semoga Anda sukses selalu.

Alat uji slump test beton

In Stock

CO-370 SLUMP TEST SET 1 SET 

ASTM C-143 / AASHTO T-119, According SNI 03-1972-1990

For determining slump/ workability of concrete both in the laboratory and in the field.

Consist of :

CO-371 Slump Cone : Heavy gauge sheet steel, 4″ top dia, 8″ bottom dia, 12″ height 1 Pc

CO-372 Inspection Scale : Machine steel, 0-10 cm slump measurement, 1 cm increment 1 Pc

CO-375 Base Plate : Steel sheet, carrying handle, 600 x 600 x 5 mm 1 Pc

GE-801 Scoop : Cast alumunium, large size, round buttom 1 Pc

GE-871 Trowel : Pointed type, wooden handle 1 Pc

GE-920 Steel Wire Brush : Wooden handle 1 Pc

GE-930 Tamping Rod : Machine steel, galvanized 16 mm dia, 600 mm length 1 Pc

Standard supply with instruction manual book

Compare
Category:

Description

Alat uji slump test beton concrete slump test

Alat uji slump test beton concrete slump test
Alat uji slump test beton concrete slump test

Concrete slump test is to determine the workability or consistency of concrete mix prepared at the laboratory or the construction site during the progress of the work. Concrete slump test is carr

The slump test is the most simple workability test for concrete, involves low cost and provides immediate results. Due to this fact, it has been widely used for workability tests since 1922. The slump is carried out as per procedures mentioned in ASTM C143 in the United States, IS: 1199 – 1959 in India and EN 12350-2 in Europe.

Features :

Alat uji slump test beton concrete slump test

  • Procedure for Concrete Slump Test:
    1. Clean the internal surface of the mould and apply oil.
    2. Place the mould on a smooth horizontal non- porous base plate.
    3. Fill the mould with the prepared concrete mix in 4 approximately equal layers.
    4. Tamp each layer with 25 strokes of the rounded end of the tamping rod in a uniform manner over the cross section of the mould. For the subsequent layers, the tamping should penetrate into the underlying layer.
    5. Remove the excess concrete and level the surface with a trowel.
    6. Clean away the mortar or water leaked out between the mould and the base plate.
    7. Raise the mould from the concrete immediately and slowly in vertical direction.
    8. Measure the slump as the difference between the height of the mould and that of height point of the specimen being tested

ALAT UJI SLUMP TEST BETON

Uji kemerosotan beton adalah untuk menentukan kemampuan kerja atau konsistensi campuran beton yang disiapkan di laboratorium atau lokasi konstruksi selama kemajuan pekerjaan. Uji kemerosotan beton dilakukan dari batch ke batch untuk memeriksa kualitas beton yang seragam selama konstruksi.
Tes kemerosotan adalah tes kemampuan kerja paling sederhana untuk beton, melibatkan biaya rendah dan memberikan hasil segera. Karena fakta ini, telah banyak digunakan untuk tes kemampuan kerja sejak 1922. Kemerosotan dilakukan sesuai prosedur yang disebutkan dalam ASTM C143 di Amerika Serikat, IS: 1199 - 1959 di India dan EN 12350-2 di Eropa.

CO-370 SLUMP TEST SET 1 SET  Ready

ASTM C-143 / AASHTO T-119, According SNI 03-1972-1990 Stock.

Consist of :

CO-371 Slump Cone : Heavy gauge sheet steel, 4″ top dia, 8″ bottom dia, 12″ height 1 Pc

CO-372 Inspection Scale : Machine steel, 0-10 cm slump measurement, 1 cm increment 1 Pc

CO-375 Base Plate : Steel sheet, carrying handle, 600 x 600 x 5 mm 1 Pc

GE-801 Scoop : Cast alumunium, large size, round buttom 1 Pc

GE-871 Trowel : Pointed type, wooden handle 1 Pc

GE-920 Steel Wire Brush : Wooden handle 1 Pc

GE-930 Tamping Rod : Machine steel, galvanized 16 mm dia, 600 mm length 1 Pc

Standard supply with instruction manual book

Dimension (l x w x h): 70 x 70 x 50 Cm / Gross weight: 30 Kg

Lainnyak : 

Reviews

There are no reviews yet.

Be the first to review “Alat uji slump test beton”

Your email address will not be published. Required fields are marked *

error: Content is protected !!
WhatsApp chat